Toilet plumbing is crucial whether you are replacing the old toilet with a remodeled version or you are installing a new one. With the help of our emergency plumbers in London, we have been able to put together this guide to improve the ease of the job. To get the best plumbing service Call for Plumbers here.
Tools Required For The Installation
The necessary tools needed to perform this installation include:
- Hacksaw
- Pliers
- Rags
- Screwdriver
- Measuring tape
- An adjustable wench
- A unity knife
- Level
- Caulk gun.
Materials Required For The Installation
- Caulk
- Wax ring
- Toilet flange
- Flexible water supply
- Brass toilet bolts.
Steps For The Installation
Proper measurement before purchasing:
Getting a plumber to replace your faulty toilets is a good idea, which is why 4D heating and plumbing are readily available to attend to your plumbing needs. To get the best Plumber service you can take Plumber Cairns easily.
However, if you wish to get a DIY session, ensure you get a rough measurement of the old toilet. For most bathrooms, the distance between the waste pipe and the wall is about 12 inches. However, for some models, the measurement varies, ranging between 10 and 14 inches.
Use a tape to measure from the wall to the toilet bolts, the analysis of that distance with the thickness of the baseboard included should be approximately 12 inches. In cases where the gap is not within this range, purchasing a new toilet may be difficult. For bathrooms that have a door nearby, be sure to get a measurement of the distance of the bowl protrusion from the wall. If you are getting a unique order toilet, the cost may generally be higher. You can visit plombier Montreal to find the best plumbing service.
Bolt Selection:
When selecting the bolt for your toilets, check the labels to ensure that you choose brass bolts and nuts. Brass is a better material for bolts as it hardly rusts, and it is easier to cut off later. For the toilet flange, buy stainless steel screws. Stainless steel does not corrode quickly or break off while driving.
Removing Old Bolts
It is a common occurrence for the pins to get stuck to the toilet after a long period. When trying to remove the pins, you may have to make use of a hacksaw blade to cut them off. Brass bolts and nuts are more comfortable to cut off. If the pin keeps spinning when you try to cut it, hold it in place with pliers and cut.
New Bolt Installation
This part of the installation process is considered the hardest. When trying to set the toilets on the original bolts, you must ensure that the pin aligns with the holes. However, this can be extremely difficult as the locks keep slipping. With every miss, there is a risk of crushing the wax ring. The option of using plastic slip-on washers can be helpful, but they still allow the bolts to move. The best option is to buy another set of machines and nuts and lock the pins in place before setting the toilet. Check the height and position of the bathroom to ensure that it is in the right spot. Locksmith Belfast is one of specialized in residential and commercial locksmith work and is an expert in lockouts and lost keys.
Fixing Flanges:
When wood rot occurs, the result is usually loose flanges. It is because the screws of the spine cannot be firm on the rotted floor. For decompositions that are not too deep, but are only under the collar, the best approach to fixing them is by using an ear-type repair ring. In this type of boxing, the ears allow screws to be driven into the solid wood away from the flange. For rots that extend beyond the spine, a section of the floor may have to be replaced.
The toilet flange is the anchor between the toilet and floor; therefore, it should be firm to avoid leaks. A damaged collar will lead to a rocking toilet, and this will cause leaks. Ensure that you scrape off the old wax ring and check the flange.
For A Damaged Flange, You Can Fix It By:
Using Shims to Eliminate the Rocking:
After properly setting the toilet in place, check for wobbles, and if you find slight wobbles, insert slip coins or stainless steel washers into the gaps under the bathroom. For more significant holes, use shims. After the wobble has been removed, tighten the nuts, cut the shims, and caulk around the base of the toilet.
Firmly Seat the Toilet in Place:
Here, the pressure squishes the wax ring until the shower settles to the floor. Trying to force the toilet down by tightening the nut on the toilet bolts may cause the base to crack. Instead, sit on the toilet and center your weight over the wax ring, then add a little pressure until the shower reaches the floor. When the shower reaches the level, use the toilet bolt nuts.
Avoid Extreme Tightening of the Water Connections:
Flexible water supply lines are much easier to install. Try getting a water supply covered with stainless steel mesh. To get a good seal, ensure that you aim the hose directly into the shutoff valve while screwing the connectors. Make them hand tight, then use pliers to add another quarter turn. To prevent leaks, ensure that the connection is not too tight. Inspect the link and tighten it further if needed.
Cut the Bolts Last:
New toilet bolts are usually extra long for easy toilet positioning; you have to cut off the excess ends after installation. However, you should ensure that cutting the locks is the last step. It is because you may find faults after fixing it, and with uncut locks, you can still make adjustments.
First, connect the waterline, then flush the toilet a couple of times to ensure that there are no leaks. After all connection confirmations have been made, you can cut the bolt. Ensure that you check for tightness after shaving, as cutting it can make the nuts a bit loose.
Bathroom plumbing requires accuracy for installations and repairs. If any of these steps seem challenging, you can contact a qualified plumber in London.